Browse Category


Appliance Repair for Common Refrigerator Issues

Nearly all homes have a refrigerator because it plays a vital role in the kitchen. Whenever it is damaged, you need to get it fixed in the next few hours before the food stuff goes to waste. Even though some appliance repairs can be solved by the owner, it is advisable to hire a professional appliance repairman. This gives you peace of mind because you can rest assured of a high-quality job, without unwelcoming surprises down the line.

There are several refrigerator problems, but the following four are the most common ones. A few of them may not need an expert if you have some basic skills to tackle them, but use an expert whenever necessary.

refrigerator repairRefrigerator Will Not Start

Starting problems may be as a result of overheating of the overload relay. When you realize there is a clicking sound while the fans are running, but the compressor cannot start, it indicates the overload relay is overheating. Some modern refrigerators may have combined overload relay with a start capacitor attached to the overload relay assembly. The start capacitor enhances starting by providing higher voltage onto the compressor windings. If the start capacitor is not working appropriately, the compressor will not start. Defective electronic control board, cold control, and temperature control may also cause compressor not to start. However, in case the compressor is faulty, you need to hire an expert to handle the repair work.

Noisy Refrigerator

Frost free refrigerators have a condenser fan that cools the condenser coil by circulating air through it, as well as evaporating defrost water from the drain pan. If the motor of the condenser fan is not working properly, it may cause noise within the appliance. Sometimes the noise may be originating from the freezer region, implying that the evaporator fan motor might not be operating normally. If you hire a repairman, he will inform you the exact source of the problem, and recommend the best solution.


Refrigerators doors have seals or gaskets that create an airtight seal when the door is closed. Damaged seals cause moisture to form along the door edge because air is leaking, leading to water leakages. When gaskets are damaged, it is advisable to replace them. In some other cases, water leakages may be caused by leaking water inlet valve. If you have a water dispenser or an ice maker, probably the inlet valve might be causing leakages if not well tightened. If the leakage does not stop after tightening, it’s nice to replace the connectors, valve body, or outlet tubing if they have cracks.

Too Warm

The air inlet damper is responsible for balancing airflow from the evaporator unit. It controls the amount of cold air entering the fresh food section, and if it is damaged, not enough cold air will be entering the compartment. The air damper housing has a Styrofoam lining and a seal to prevent air leakage. Therefore, it is ideal to hire a qualified technician to inspect the housing to prevent damage to the seal.


Reglazing And Not Replacing Your Bathtub Is The Best Decision For Your Bathroom

When your wall’s color gets damaged, you immediately consider repainting it. When your home’s flooring gets dirty, you will consider polishing it. Whenever your bathroom fitting gets leaky, you can repair or replace them. But what happens when your tub has lost its once classy finish? After several years, your tub can begin to look old and lose its one prime glaze. The glossy shine of your tub is one of the factors that will add to your bath’s beauty. A gorgeous looking tub can be the focal point of your bath. And just like other thing…

Why Not Reglaze And Refinish Your Bathroom’s Bathtub?

With advanced technology these days, people have discovered innovative ways on how to reuse the things that they already have, restoring materials into their lovely original state and in many cases, even make it appear better. This is especially true for reglazing your bathtub and even though this task has been practiced since the early 1950s, there are still a few of us who aren’t aware of this option. Since this practice has been used, strategies for achieving excellent results have dramatically improved, prolonging the life of your present assets for far lesser than the cost of an overall replacement.

Bathtub reglazing is the process of giving your tub that new finish and make it appear as glossy as it did when you first bough it. There are several ways for you to refinish your tub. A bathtub refinishing procedure will not take as much time and also doesn’t damage your current bathroom décor and other fixtures. A tub resurfacing project is something very convenient and affordable compared to a total bathroom fixture replacement.

A new installation project would typically include a demolition process to remove your worn out bathtub. The demolition can eventually destroy floors, walls, and tiles and may also need plumbing adjustments. This is usually a very long process and may take several weeks to complete.

Keep Reading